#Kpg 49D Code Can Be#
#Kpg 49D Serial Number Of 30100001#

Kpg 49D Serial Number Of 30100001

TK-480/481 transceivers with a serial number of 30100001 or greater have a red triangle in the KENWOOD logo label (B43-1139-04) on the front panel. You cannot use the KPG-35D for those radios. You must use the KPG-49D to program TK-480/481 trans-ceivers with a serial number of 30100001 or greater.

Service manual for kenwood tk 3202 download. The KPG-46 and KPG-4 programming cables are available in either USB or serial port DB-9 connectors and either will work fine with KPG-49D. The KPG-46 is a 8-pin RJ-45 connector and the KPG-4 has a 6-pin RJ-12 connector and will work just fine being plugged into the TK-981вЂ™s RJ-45 8-pin microphone connector. 02 Program Software for TK-190.Kpg-49d Version 4.20 Download. Disclaimer While every precaution has been taken in the preparation of this manual, Kenwood assumes no responsibility for errors or omissions.Software Nomenclature : Radios Associated With : Radio Use Manual: Radio Service Manual: Other Radio Information: KPG-49d v 6. No part of this manual may be reproduced, translated, distributed, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, for any purpose without the prior written permission of Kenwood.

Turn clockwise to switch On the transceiver. Model Trunking mode Conventional mode Transceiver Power and Volume switch. The programmable features are summarized. Operation Features The TK-480/481 is an 800/900MHz band EFJ LTRв„ў-compatible trunked radio designed to operate in both trunked and conventional modes.

If all systems are locked out, the scan stops and only the revert system is received. If there a locked system, the Delete ( ) indicator flashes during fixed scanning. The revert system is scanned even if it is locked out. The Delete ( ) indicator disappears to indicate that the system has returned to the scan sequence. 2-4.TK-480/481 OPERATING FEATURES To unlock a system, select the system and press the key. Use this function when the transceiver is required to be more simple operated.

Kpg 49D Code Can Be

If the option signalling matches, a predetermined action will occur. It is possible to use individual call, group call, D.B.D. DTMF Built-in DTMF decoder is available for option signalling. If there is no system to be accessed, an intercept tone sounds, the mode is terminated, and the transceiver returns to the first system.TK-480/481 OPERATING FEATURES 5. This code can be up to 6 digits from 0 to 9 and input with the keypad or selector, and вЂњSвЂќ key. Radio password When the password is set in the transceiver, user can not use the transceiver unless enter the correct password.

The communication area is much wider than 2400bps. 1200bps : Data communication is made in 1200bps. The same rate must be set as a communication partner. Please notice that the following status numbers are used for special purposes MSK data baud rate setting. Entering these statuses from the DTMF keypad can be inhibited. The transpond or alert tone will sound.TK-480/481 OPERATING FEATURES в– Status 80~99 (Special) в– FleetSyncв„ў Baud Rate Status numbers from 80 to 99 are reserved for special purposes.

The optional feature's control tone can be set to yes or no.TK-480/481 OPERATING FEATURES / REALIGNMENT 7-16. Password Agreement Tone в– TX Busy Wait Time When the correct password is entered, the tone sounds. Release code is received, transpond tone sounds. Increase this item to improve data communication reliability. DBD Off Tone Number of Retries is the maximum number of retry transmission when no acknowledgement is received in the Maximum ACK Wait Time.

Preface The TK-480/481 transceiver is programmed by using a personal computer, programming interface (KPG-36) and programming software (KPG-49D). (The mid tone and low tone are output alternately in 200ms intervals.) 7-17.TK-480/481 REALIGNMENT 5. It is output until the PTT button is released. It indicates that the PTT button is pressed, and transmission has started, but the repeater cannot be connected and talking is not possible.

When programming the firmware, it is recommend to copy the data from the floppy disk to your hard disk before update the radio firmware. This mode cannot be entered if the Firmware Programming mode is set to Disable in the Programming software (KPG-49D). To start the Firmware Programmer from KPG-49D, the Fpro path must be set up by KPG-49D Setup. When the POWER switch on, user mode can be entered immediately. Connect the TK-480/481 to the personal computer with the interface cable. Figure 1 shows the setup of an IBM PC for programming.

Audio amplifier circuit 3-4. RF unit An incoming RF signal from the antenna terminal is passed through the antenna switch (D7, D9, and D10 are off) and then the bandpass filter (L11).TK-480/481 CIRCUIT DESCRIPTION 3-3. Receiver System This transceiver is an 800/900MHz band EFJ LTRв„ў trunked system compatible FM portable transceiver that can be programmed to operate on both LTR and conventional systems. 6-4.TK-480/481 CIRCUIT DESCRIPTION 1.

Frequency Synthesizer Unit 6. When encoding DTMF, mute switch (Q7) is turned OFF for muting the microphone input signal.TK-480/481 CIRCUIT DESCRIPTION 5. Drive and Final amplifier The signal from microphone passes through the limitter circuit in D11, and through the high-pass filter, the ALC circuit, the low-pass filter, the high-pass filter, and pre-emphasis/IDC circuit in IC12. The signal then goes through an AF amplifier IC3 (2/2), an electronic volume control (IC4), and an AF switch (Q310 is on), and is routed to audio power amplifier (IC300), where it is amplified and output to the internal speaker.TK-480/481 CIRCUIT DESCRIPTION 4-2.

3) Sending frequency program data to the PLL.TK-480/481 CIRCUIT DESCRIPTION 6-2. 2) Reading system, group, frequency, and program data from the memory circuit. IC15 mainly performs the following 1) Switching between transmission and reception by PTT signal input. It controls the TX-RX unit and transfers data to and from the display unit.

The signal is input to pin 23 of the CPU. Low-speed data (QT,DQT,LTR) F1 +B The demodulated signal from the IF IC (IC9) is amplified by IC8 (1/2) and passes through a low-pass filter (IC10) to remove audio components. 5.8V), a beep sounds and transmission is stopped.TK-480/481 CIRCUIT DESCRIPTION 7-2. If the battery voltage falls even more (approx. When the battery voltage falls below the voltage set by the Low Battery Warning adjustment, the red LED flashes to notify the operator that it is time to replace the battery.

4 DTMSTD I DTMF decode IC data detect input. 39 HOLD 2 HSDOUT O High speed data output. Port name I/O 1 LSDOUT O Low speed data output.

Port 1 STRB Port name ES Function Pin No. 7 CNVSS I GND.TK-480/481 SEMICONDUCTOR DATA Shift Register 1 : BU4094BCFV (TX-RX Unit IC18) Shift Register 2 : BU4094BCFV (TX-RX Unit IC19) Pin No. 44 WR - Flash memory WR bus.

Kpg 49D Manual